The Select LED’s have the versatility and unique features which make it the perfect imaging tool for use in any studio production or on location. The detachable controller can operate the fixtures remotely with a 25ft (*m) extension cable. For further flexibility, the controller can be attached to the back of the fixture or mounted onto a stand using the ballast mount (MTP-BAL)) accessory. Slim in profile at only 3 inches, the portable lightweight fixture can be rigged in tight places or screwed onto a wall or ceiling through its eyelets.
The Select LED lights include dial-in variable color temperature control, full-range dimming and programmable 2700K to 6500K presets. The Select LED’s soft white light is flicker-free and does not shift color temperature when dimmed. Light levels are consistent throughout the Kelvin range.
In addition, Kino Flo introduces a Green/Magenta control to match the spectral sensitive curves of the most popular cameras and other light sources. With built-in DMX and Lumen Radio® receivers, the Select LED’s can be controlled by DMX and/or wireless DMX. Wireless capability eliminates the need for DMX cables. Rounding out the Select LED’s attributes is the ability to run on universal input from 100-240VAC, or 24VDC with as little 1.3A, 120VAC.
Select LED Fixture
• Built-in Barndoors
• Removable Honeycomb Louver
• Twist-on, locking Center Mount
• Kelvin presets & custom settings, 2700K-6500K
• Universal input 100VAC-240VAC or 24VDC
• Remote Controller
• Manual & DMX Dimming w/ Auto Terminate
• DMX wireless (Lumen Radio)
• Green/Magenta control
• Flicker-free, dead quiet operation
• Five Kelvin presets
• Dial-in color temperature control between 2700-6500K
• Can use preset buttons to store custom Kelvin settings
• Light levels do not change when selecting Kelvin settings
• Color-correct with high color rendering index (CRI 95)
• Universal Input 100VAC-240VAC or 24VDC
• Energy efficient, draws 1.3A, 120VAC and 7A, 240VDC
• Flicker-free, dead quiet operation
• Full range onboard and DMX dimming
• DMX wireles link (Lumen Radio)
• DMX Auto Terminate
• Green/Magenta control
• No color shift while dimming
• Remote fixture with built-in barndoors
• Fixture includes 90° Honeycomb Louver
• Honeycomb louver also available in 60°
• Removable Center Mount
• Mounts to stand, light enough to be hand-held
Select LED System
The Select LED System consists of four components: Select LED Fixture (fig. 1), Mounting Plate (fig. 2), LED Controller (fig.3), and Extension Cable (fig.4). It was designed in this manner to allow the greatest flexibility in lighting solutions for challenging situations.
Select 30/20 LED Fixture
The Select LED fixture includes a removable 90° Louver. The fixture has a twist-on mating plate to accept a removable twist-on Center Mount. The remote Controller can also be attached to the back of the fixture with Velcro.
Besides the plastic louvers, another light control option is a Flozier available in half f-stop. The Flozier attaches to the barndoors and can be adjusted to various configurations.
One of the design features of the Select Fixture is the twist-on removable Center Mount. When it’s on, the fixture mounts easily to a light stand; when it’s off, the fixture is flat and can be hand-held, or hidden in a space too small to place a stand-mounting fixture. When the mount is removed, the grommet holes along the edge of the fixture are designed to allow the fixture to be screwed
to a wall or ceiling through its eyelets.
The standard mount comes with a Baby Mount that mounts onto a baby stand. The ball and socket mount allows the fixture to be oriented in a broad range of angles. There is also a short version and mount w/ 3/8″ pin (see below) available as accessories. The yellow wire loops are there to provide attachment points for a safety chain
Mounting options include MTP-KF41 Mount with 3/8″ Pin (10mm); MTP-BC41 Mount with Baby Receiver Curve (16mm);
MTP-BF41S Mount with Baby Receiver Short (16mm).
MTP-L Kino 41 Lollipop w/ 3/8” Pin
MTP-LBC Kino 41 Lollipop w/ Baby Receiver Curve (16mm)
MTP-LBS Kino 41 Lollipop w/ Baby Receiver Short (16mm)
The tension on the lock lever may be adjusted by pulling the handle away from the mount.
This disengages the handle from the screw mechanism and allows the lever to be reoriented.
The Kino Offset w/ Baby Receiver, MTP-B41F (sold separately) can be used to center the weight and balance of the fixture on a stand.
It can also be under slung from a baby stand to use as an up light.
A Ballast Baby Mount (MTP-BAL) is available as an accessory.
The Select 150 LED Controller
The Select LED Controller includes state of the art features with dial-in variable color temperature control, full-range dimming and programmable 2700-6500K presets. It operates flicker-free and does not shift color temperature when dimmed. Light levels are consistent throughout the Kelvin range. The controller can be used remotely with a 25ft extension cable or can easily be attached to the back of the Select LED fixture with Velcro.
With built-in DMX and Lumen Radio® receivers, the Select LED’s can be controlled by DMX and/or wireless DMX with DMX auto terminate.
In addition, the LED Controller features a Green/Magenta adjustment to match the spectral sensitive curves of the most popular cameras and other light sources. The energy efficient LED Controller runs on universal input voltage from 100-240VAC at only 1.3A (120VAC)
(Select 30) or can also operate 24VDC using only 7A.
Select 150 LED Controller Control Panel
A) On / Off: On = Green light displayed. Off = Red light displayed.
B) Menu: Provides General Setup, DMX Setup, Wireless DMX Setup.
C) Kelvin Preset Buttons: Kelvin buttons come preset at the factory. Factory defaults left to right are: 2700K, 3200K, 5000K and 6500K. User acan also use these preset buttons to store custom Kelvin and Hue settings.
D) Display: Provides Kelvin, Dim level, Hue and DMX channel.
E) Lock: In Lock mode, a red light is displayed. To reset Kelvin to factory presets, hold the Lock button for 3 seconds.
F) Mode: Selects Hue, DMX, Dim and Kelvin settings.
G) Micro USB: For software updates
H) Dimmer Knob: Manually adjusts Kelvin or Dim levels Hue and DMX channels. Press the knob to toggle between fine and coarse adjustments.
Note: Each Select 150 DMX Controller has an “AUTO TERMINATE” feature. The last fixture that does not have an XLR cable attached to the DMX “Out” port will automatically terminate.
The Select 150X LED Controller is powered AC and includes an IEC connection. The controller includes universal input from 100-240VAC.
The Select 150X LED Controller can also be operated on 24VDC (input range 18-36VDC) through a 3-Pin xlr. The pin polarity is:
Pin #1 – Ground
Pin #2 – +18-36VDC
Pin #3 – Not used
The Select LED includes a built-in Lumen Radio receiver and can be operated wirelessly with a Lumen Radio transmitter (sold separately). Wireless is an option to using DMX cables. For more information on Lumen Radio Receiver/Transmitter, see www.LumenRadio.com.